What to do if the roof is leaking
During bad weather, hurricanes, snow blockages, a shift of one centimeter of the slate sheet and even with millimeter installation defects, leaks occur in the roofs. And here the speed of localization is directly proportional to the further functioning of the building.
Here is a company that performs a wide variety of repair and construction work http://stroyimpuls-vrn.ru/uslugi/remontno-stroitelnye-raboty, so in case of force majeure in the form of a damaged roof, you should try to eliminate the threat with lightning speed. Otherwise, the situation is fraught with problems from short circuiting, but mold around the common perimeter.
The "ambulance" algorithm for a damaged roof depends entirely on the material from which it is made. There are two common coatings - slate and corrugated board. The features of the materials can be found at https://www.google.ru/.
Slate roof leaking what to do
Before localizing a leak in a slate roof, you should understand its structure. The slate covering is placed on the roofing felt, which wraps around the shawl. Both the roofing material and the slate itself are securely fixed. If there is a sharp leak, then presumably both the sheets and the roofing material itself are significantly damaged. If the leak is weak and spreads slowly in the form of a dark spot, then, as an option, either the sheets themselves or the joints were damaged. From the hurricane wind, the position of the ridge is conceived. If the leak is not in the form of a spot or in the form of drops, but by darkening, the problem is in the joints. As a short-term help, put an additional slate sheet on the suspected leak. If the slate roof is leaking again, what to do?
In case of emergency "patching", the flow will not stop immediately, the slate roof is two-layer and with an obligatory attic floor, where water has already accumulated. But if the active flow does not stop even after half an hour, then you should clean the roof of debris, check the waterproofing of all joints, because water can seep to the ceiling and not from the place where the roof actually lets through. Then, from the attic dark floor in the daytime, just inspect it from the inside. Coverage gaps will help you understand where the problem is.
After detecting a problem, it will be enough to change a slate fragment or a slate fragment and a roofing felt substrate. And if the roof is leaking, what to do if the roof is leaking with insulation?
Heaters from moisture are destroyed. The most resistant is polystyrene and polyurethane foam. If mineral wool is used as a heater, everything is much more complicated. This material quickly absorbs moisture and will dry out for a long time after eliminating the leak. In the case of an excessively long drying process and in the absence of antifungal treatment, mold may appear, which will not add strength to the entire structure. This moment is vital to consider.
Roof leaks in a private house what to do? The roof is leaking in an apartment building - the difference
If the roof of a private house is leaking, what to do? It is much easier to fix a leak in a private house. Permanent access to the attic space is open and there is always the right "piece" for temporary localization at hand. Worse, if such a problem overtook a resident of the last floor of an apartment building. But according to the law, utilities are obliged to solve such a problem, and in case of damage to the equipment of the apartment, theoretically, its cost can be reimbursed through the courts from the same utilities.
Roof leaks from corrugated board what to do
Roof leaking from corrugated board what to do? Decking is a more hygienic and aesthetically pleasing material for roofing than slate. If the indicated problem begins to arise, then the roof made of corrugated board will be incomparably more troublesome. The reason is that fragmentary replacement is much more complicated here.
How to close up a leak in a roof from a corrugated board. Algorithm.
First, we find out the reason. The corrugated board has two vulnerabilities: the joints of the sheets and the joints with the crate. In the second option, it is wiser to make a complete overlap, because the costs of materials in this case and in the case of "patching" will be practically the same. And in the event of a leaking joining of sheets, the problem can be solved.
How to repair a leak in a roof from corrugated board in case of damage to the joint of sheets
The easiest way to solve the problem in case of leakage from the seams around the entire perimeter is gluing with a special sealing tape. Manufacturers for such an insulator give a multi-year warranty and this is considered one of the low-cost way to solve the problem. More expensive - sprayed waterproofing for the entire surface. Sometimes such a composition is used to increase the service life of slate as well. The advantages of such a restoration: the service life of the roof increases by at least ten to fifteen years, provided that a new roof is covered. There is noise reduction from the "knock" of raindrops and hail. This material can be successfully used by a non-professional builder. Cons - cost. Expensive.
Another option is waterproofing and fiberglass. That is, first, the seams are treated with hydrosol, on which the fiberglass is placed. After drying, two layers of hydrosol again. Also, in turn, letting the surface dry.
How to protect yourself from roof leaks and the biggest danger in case of hydraulic damage
- 1. After an emergency localization of an active leak in the roof of any material, if the attic floor is heavily flooded with water, you must immediately disconnect the entire building from electricity. At the slightest defect in the surface of the wiring in a humid environment, a short circuit will surely occur, and then a fire may begin.
- 2. To prevent roof leaks and save yourself from many expenses in the future, roofing works are not carried out independently. Even a one-degree incline or unevenness can lead to leakage. It is better to purchase consumables of really guaranteed quality - it will be much more reliable.
Master Tips
Prev Next
To prevent the oil paint from drying out during storage and to prevent the formation of a film on it, put a circle of thick paper on the surface of the paint and “fill it with a thin layer of drying oil.
"The plastic wrap covering the balcony or greenhouse is protected from breaking by the wind by a string stretched on both sides with intervals of 10-15 cm."
"Clay is usually added to make concrete mix easier to handle, but clay will reduce the strength of the mix. Add a spoonful of detergent to the mix for a bucket of water."
"To prevent the screw, the head of which is hidden behind an obstacle, from rotating together with the tightened nut, you need to put several turns of thread or thin wire over it and slightly tighten the ends. Friction holds the screw well in place. The ends of the thread can be cut after tightening."
"You can cut out a birdhouse entrance without a brace. It is enough to split the front side of the board in the center and cut out the half-holes of the required size with a chisel or a hatchet, and then reconnect the halves."
Wooden screw caps will crumble and fall out of the wall. Take your time to cut a new plug. Fill the hole in the wall tightly with a capron from an old stocking. With a red-hot nail of a suitable diameter, melt the hole for the screw. The fused nylon will turn into a solid cork.
"A carpenter's level is easy to turn into a theodolite, by equipping it with a sighting device made of a slot and a front sight."
"In order for two strips of linoleum to lie end-to-end, it is convenient to use a self-adhesive decorative film, placing it under the base of linoleum."
"In order for the nail to go in the right direction and not bend when driven into a deep hole or groove, place it inside the tube and secure it with crumpled paper or plasticine."
Before punching a hole in the concrete wall, secure a piece of paper just below it. Dust and concrete debris will not fly around the room.
"To cut the pipe exactly at right angles, we advise you to do this. Take a straight strip of paper and screw it onto the pipe along the sawing line. The plane passing through the edge of the paper will be strictly perpendicular to the axis of the pipe."
"Turning over logs or wooden beams will be helped by a simple tool - a segment of a motorcycle or bicycle chain, supplemented with a hook on one side and a tom on the other side attached to a scrap yoke."